Pump Selection: Overview
This overview shows all 32 combinations of fluid, application, flow rate, and operating pressure, along with the corresponding pump series. It contains the same information as the Pump Selector, but all on a single page.
The Three Fluid Categories
- Water/water-like media
- e.g., drinking water, clean process water, saltwater, chemicals, non-abrasive media with less than 1% solids content
- Fluids/flowable slurries and liquids
- e.g., primary/secondary sludge (biological), mine tailings, ash slurry, foundry and steel mill slurries, oil sludge, ceramic slurry, paints, varnishes, adhesives, glue
- Non-flowable slurries
- e.g., dewatered sewage sludge, bio solids, pastes for mine backfilling
How to Read the Tables
- The limits are given as lower and upper bounds. “over 30 up to 70 m³/h” means: greater than 30 and at most 70.
- The pump selector does not query all criteria in every scenario. Where it does not, the table lists the range covered by the recommended series for that parameter.
- If the pump application is unclear, “Transfer” applies. This provides the widest selection of series.
- Multiple series listed in a single row are equally suitable. Which one is better in a specific case depends on boundary conditions not shown in this overview.
Selection for Water/water-like media
| Application | Flow rate | Pressure | Recommendation |
|---|---|---|---|
| Transfer | up to 30 m³/h (132 gpm) | up to 0.6 MPa (87 psi) | EM |
| Transfer | up to 30 m³/h (132 gpm) | over 0.6 MPa (87 psi) up to 2.5 MPa (362 psi) | CM, HMD |
| Transfer | up to 30 m³/h (132 gpm) | over 2.5 MPa (362 psi) | HMD, HPT |
| Transfer | over 30 m³/h (132 gpm) up to 70 m³/h (308 gpm) | up to 10 MPa (1450 psi) | HMD |
| Transfer | over 70 m³/h (308 gpm) | up to 25 MPa (3625 psi) | HMT, HMQ |
| Filter press cloth washing | up to 28 m³/h (123 gpm) | up to 16 MPa (2320 psi) | HP |
| Gland seal water supply | up to 50 m³/h (220 gpm) | up to 25 MPa (3625 psi) | CM, HPT |
| Reverse osmosis | up to 50 m³/h (220 gpm) | up to 25 MPa (3625 psi) | HP, HPT |
Selection for Fluids/flowable slurries and liquids
| Application | Flow rate | Pressure | Recommendation |
|---|---|---|---|
| Transfer | up to 15 m³/h (66 gpm) | up to 0.6 MPa (87 psi) | EM |
| Transfer | up to 15 m³/h (66 gpm) | over 0.6 MPa (87 psi) up to 2.5 MPa (362 psi) | CM, HMD |
| Transfer | up to 15 m³/h (66 gpm) | over 2.5 MPa (362 psi) | HMD |
| Transfer | over 15 m³/h (66 gpm) up to 30 m³/h (132 gpm) | up to 0.6 MPa (87 psi) | EM |
| Transfer | over 15 m³/h (66 gpm) up to 30 m³/h (132 gpm) | over 0.6 MPa (87 psi) | HMD, CM |
| Transfer | over 30 m³/h (132 gpm) up to 70 m³/h (308 gpm) | up to 4 MPa (580 psi) | HMD |
| Transfer | over 70 m³/h (308 gpm) | up to 25 MPa (3625 psi) | HMT, HMQ |
| Filter press feeding | up to 15 m³/h (66 gpm) | up to 0.8 MPa (116 psi) | EM |
| Filter press feeding | up to 15 m³/h (66 gpm) | over 0.8 MPa (116 psi) | CM |
| Filter press feeding | over 15 m³/h (66 gpm) up to 90 m³/h (396 gpm) | up to 2.5 MPa (362 psi) | HMD |
| Filter press feeding | over 90 m³/h (396 gpm) | up to 2.5 MPa (362 psi) | HMQ |
| Spray dryer feeding | up to 20 m³/h (88 gpm) | up to 2.5 MPa (362 psi) | CM |
| Spray dryer feeding | up to 20 m³/h (88 gpm) | over 2.5 MPa (362 psi) | HMD |
| Spray dryer feeding | over 20 m³/h (88 gpm) up to 40 m³/h (176 gpm) | up to 4 MPa (580 psi) | HMD |
| Spray dryer feeding | over 40 m³/h (176 gpm) | up to 25 MPa (3625 psi) | HMQ |
| Incinerator feeding | up to 15 m³/h (66 gpm) | up to 2.5 MPa (362 psi) | CM |
| Incinerator feeding | up to 15 m³/h (66 gpm) | over 2.5 MPa (362 psi) | HMD |
| Incinerator feeding | over 15 m³/h (66 gpm) | up to 4 MPa (580 psi) | HMD |
Selection for Non-flowable slurries
| Application | Industry | Flow rate | Recommendation |
|---|---|---|---|
| Transfer | Mining | up to 30 m³/h (132 gpm) | SDS |
| Transfer | Mining | over 30 m³/h (132 gpm) | HMT, HMQ |
| Transfer | Wastewater | up to 30 m³/h (132 gpm) | SDS |
| Transfer | Other | up to 30 m³/h (132 gpm) | SDS |
| Transfer | Other | over 30 m³/h (132 gpm) | HMT, HMQ |
| Incinerator feeding | all industries | up to 30 m³/h (132 gpm) | SDS |
Pump Series Overview
EM – Electric Diaphragm Pump
The energy-efficient pump for low-pressure applications.
Industries: Chemical industry, Ceramics, Food, Wastewater, Corrugated cardboard manufacturing
CM – Compact Diaphragm Pump
The double-diaphragm piston pump, designed for a particularly high level of safety.
Industries: Chemical industry, Ceramics, Oil & gas, Cement
HMD – Piston Diaphragm Pump
The smart pump with AI pump monitoring for exceptionally high pump availability and low operating costs.
Industries: Mining, Chemical industry, Energy, Ceramics, Wastewater
HMT – Piston Diaphragm Pump
The HMT is designed for flow rates of up to 210 m³/h. Its robust pump design ensures exceptionally low-pulsation flow. AI monitoring enables predictive pump maintenance.
Industries: Mining, Chemical industry, Energy, Ceramics, Wastewater
HMQ – Piston Diaphragm Pump
The HMQ is designed for flow rates of up to 410 m³/h and has proven itself time and again, particularly in mine backfilling and fly ash transport. AI monitoring enables predictive pump maintenance.
Industries: Mining, Chemical industry, Energy, Ceramics, Wastewater
HP – High-Pressure Pump
High-performance triplex pump for cleaning filter cloths in chamber and membrane filter presses.
Industries: Chemical industry, Oil & gas
HPT – High-Pressure Pump
Robust plunger pump for demanding industrial applications.
Industries: Chemical industry, Oil & gas
SDS – Solids Diaphragm Solution
The smart solids pump with AI pump monitoring for predictive maintenance and without hydraulic power unit.
Industries: Wastewater
Go to Pump Selector, which guides you to the right series by answering a few questions